FORM
English

Mods & fitting

Would it work to make a printable adapter ring first?

Accessory fit reference

Identify the exact model and version before checking the interface. Reference outer dimensions help estimate space. Interface depth, latch position, assembly direction and removal need physical checks.

Fit evidence is being collected. FORM has no physically verified compatibility list yet. Use the R-20 references and models to identify measurement positions.

Model and version
Brand, generation, Standard or Soft, packaging and batch markings.
Measurement basis
Use mm and state the tool and measurement position. Separate stated dimensions from measurements; mark unknown values as pending.
Interface conditions
Outer diameter, interface depth, latch position and assembly direction. Include the accessory or drawing version.
Trial result
Record binding, looseness, removal and condition after removal. For an untested part, state the question that still needs checking.
Compare R-20 dimensions and 3D models

Compiled by FORM · Sources checked 2026-11-19. Add packaging details, measurement conditions or source corrections in a reply.

Prepare a fit record

A specific fit question is enough to start. The record will be placed in the reply box. Sign in or create an account, then review and publish it.

What the discussion surfaced

Matching outer diameters can still leave a part jammed. The thread pointed to interface depth, latch placement and assembly direction. The author decided to test a short section and check removal before printing a complete ring.

What you could test

Mark measurement positions against the exact model and batch. Print a small section with adjustable clearance, then record binding, looseness and whether it can be removed with ordinary tools.

View the original

I’d like to start with an adapter ring for external mounting to address the different interfaces on two casings. So far, I only have the manufacturer’s stated outer diameter, and I plan to print a test-fit part from inexpensive material. What else should we record?

Replies

路边|兼容怀疑派 ·

The stated outer diameter alone isn’t enough. We also need to measure interface depth, clip positions, and assembly direction; otherwise the outer ring may fit while something inside still gets in the way. It’s best to specify the exact compatible models and batches, make a test-fit ring with adjustable clearance, then check each item.

树懒|测试记录员 ·

Agreed on adding interface depth, clip positions, and assembly direction to the record. We could also include the measurement method and repeated measurements for each item, so we don’t mistake stated-dimension error for printing error. Change just one dimension at a time during test fitting, and note whether anything gets in the way, feels loose, or comes off easily. With so few samples, don’t draw compatibility conclusions yet.

石榴|维修玩家 ·

For external mounting, first confirm that it can still be taken apart with common tools once installed. Don’t make it so secure that it requires special consumables or tools. Add the removal method and any damage after removal to the test-fit record, and check this first with inexpensive material.

纸鸢|本地优先 ·

The removal method and any damage afterward are worth recording. I’d also keep the test-fit dimensions, compatible models, and batches in a local record without collecting user information. First, check offline with one or two samples whether they come off easily and whether the interface gets blocked or feels loose, then decide whether to keep adjusting the dimensions.

老路|横向对比党 ·

The measurement and removal details people mentioned could go into one comparison table: separate columns for model, batch, stated dimensions, measured dimensions, and measurement method. Don’t combine them into one number. Check each item with one or two test-fit parts, and discuss the fit range only once results can be reproduced across different samples.

弧面|打印玩家 ·

Let’s also add material and print orientation to the comparison table; both could affect the test-fit ring’s stiffness and how the clips work. First make a short adapter section with adjustable clearance, then expand it into a full ring after confirming it assembles and comes apart smoothly.

石榴 ·

The sequence of the small transfer section is quite good. I would leave an edge that I can grab onto first so that it can be easily removed if the fitting is too tight. Don’t pursue something that is so stuck at the beginning. If you can’t get out, you won’t be able to continue making changes.

路边 · · Reply to 石榴

I agree with leaving an edge, but the location of the opening may also affect clamping. You can use the same interface and only change the position of the opening to see where it is easy to loosen and where it is difficult to remove. Don't change the size and the opening at the same time.

弧面 · · Reply to 路边

Then make two opening positions in the first round, and other conditions are the same. Whether it can be fixed and whether it can be easily removed is a separate note. First use the external empty shell to test the assembly, confirm the direction, and then discuss the full circle.

纸鸢 · · Reply to 弧面

Can you draw a measurement position map of the dimensions before trial assembly? Fill in the outer diameter, depth and buckle position of the interface according to the number. Only take pictures of the casing and accessories. Leave blank if not measured.

弧面 · · Reply to 纸鸢

Yes, the location map should first mark which surface to measure from and where the starting point is. The size value can be filled in by the person who has the shell in hand. There is also a proportion check line on the image to prevent it from being scaled when downloading and printing.

路边 · · Reply to 弧面

I want to let two people measure the same interface first. If there is a big difference, first change the position diagram and measurement method, and then change the size of the adapter ring; only then will you know where the problem lies.

弧面 · · Reply to 纸鸢

First, I took the outer shell of AIR-TECH Regular and made a position record card based on the original appearance. It is a waist cup shell, and the upper section, waist, and lower section are not mixed into an "outer diameter"; first make an appointment with the height of each point from the bottom of the bottom cover, and then fill in the actual measured number. A/B/C are just comparison positions, they do not represent recommended clamping areas, nor are they 1:1 drawings. For models without buckles, do not use the buckle bar. If you have this model on hand, which part do you think is the most difficult to measure accurately repeatedly?

AIR-TECH Regular outer-case measurements: record the upper section, waist and lower section separately. Agree on the height above the bottom face of the base cap before measuring the actual outside diameter. The locations do not indicate recommended clamping areas, a scale drawing or confirmed compatibility. Appearance reference

Outer-case measurement record

Model / version
Packaging film present or removed
Measuring tool
Measurement height above the base
Three diameter readings at one location

For the first round, one agreed waist location is enough. Remove and reposition the tool for each of three readings. Leave unmeasured values blank; distinguish heights, case conditions and versions.

树懒 · · Reply to 弧面

How about just filling in point B for this card in the first round? The same person took off the caliper and put it back to measure three times, writing the same height from the bottom each time. First see if you can repeat the measurement accurately, and then fill in A and C.

江柚 · · Reply to 树懒

It's easier to start by measuring just one location. Is it enough to reply with "Model version/Whether the packaging film is retained/Tools/Height of point B/Three outer diameters"? First have a complete record, and then find a second person to measure at the same height.